Forumsee logo
Forumsee » Cars

Messages labeled as 'Ford'

1 2 3 4 5 6 7 Next >>   25 50 75

Today

92 lx coupe, 4cyl auto. Is being converted to a carbed 5spd car. Does anything need to be done with the wiring from the transmission so the ignition will work properly? There i...
Ok, a friend of mine is putting my car back together. I'm wondering if you all could help me figure out what the motor will make and what I can expect for 1/4 mile times from it...
1. EVTM - Electrical and Vacuum Troubleshooting Manual 2. Service Manual 3. PCED - POWERTRAIN CONTROL/EMISSIONS DIAGNOSIS
Brought a 91 turd back to life and put my 408W in it with a TKO 600. Went with a simple setup to get it going, mech fuel pump, 750 quick fuel, HEI one wire dist, etc. Will...
Hey guys, got a small dilemma I'm trying to decide on. I've got a nearly virgin 69 351W 4bbl (flat top pistons with 4 valve reliefs) short block - a family friend took it ...
Finally got the new motor and tranny installed. Boss 5.3 shortblock, b-heads with stage 3 crower blower cams, stock intake with accufab, 60lb injectors, bassani midlength header...
I have been battling not enough fuel. I have reworked the whole fuel system. My system now is dual fpdm's, dual aremotive 340's,dual bap's and -8 fuel line. All wires are upgrad...
Is anyone from the SLC area and know of a good dyno-tuner in the area. I am looking for someone who can tune SCT but i am having troubles finding a shop. I am looking to tune my...

Yesterday

I recently picked up a 2014 Ford F150 XLT supercrew. I am going to a basic system in the truck. I will be using the following components: Kicker 43CSS68 6x8 comp speakers for...
Has anyone run all Mechanical gauges on their 95 ? The only gauge that work on my is the is the fuel level. So I want to switch to mechanical one in. What needs to be done to ...
no over heating ... the first time i was getting heat problems for months then finally just getting worse and worse. This time the car ran great until one day was givivng WOT on...
This will be for a street/strip car, has an Astro A5, not interested in going with a T6 now, stock block w/ a girdle. I'll be running E85 and would like to keep it around 600-70...
I installed the dash below in my 1993 LX. Looks awesome but alternator doesn't work. Dash Pic: I realized that I needed to hook up/ splice wires for the exciter ci...
Hi guys looking for some info. Have a 94 306 fully balanced e cam, headers etc with BBK upper lower rails and reg. Anywho, I'm new to nitrous and looking to put a 150 on it. Wha...
I heard something about a module for the air bag being located behind the radio that causes this beeping and wanted to confirm before I take my car apart again. Is there a w...
I want to flush the power steering on my 03 mach1. There are 2 lines on the drivers side that go to the tube cooler. Which is the return line, the upper or lower hose?
I have a 351w on my 85 gonna be pushing 600HP and was looking for a good clutch. I am running a faceplated TKO 600 tranny. I can get a good deal on a spec stage 5 clutch but Li...
I recently picked up a mustang with a 351 in it that is a project car about 80% done. The motor is built for boost so I am building a twin turbo setup for it. The car came wit...
I recently swapped a Mach 1 engine, trans and harnesses into my 96 gt. I have a few kinks to work out and would appreciate any help. First, my gauges stay on at all times even w...
Can anyone confirm the silver used for the above car wheels please? I am assuming it is the same for the bumpers? Thanks
So its official Ive joined the 25XX lb club and enjoying it rather nicely. Got the car on scales at NJMP last weekend and she was 2643 (with my helmet, gloves, neck collar and ...
Just bought a 1990 2.3 LX with auto transmission. The woman I got it from drove it up to the shop a couple weeks ago to get a new muffler put on, when they were done working on ...
I am looking at buying an edge racing converter for my C4 and just wanted to get some opinions on their stuff.......
Tranny is a build aod with a lentech manual vb with a brake. Its working perfectly until i do a quarter mile pass or just a dyno pass in third gear. After stoping the car and tr...
I am working on a newly acquired '64 Comet, with a 5.0 HO and AOD swapped in it. The car generally runs pretty well, but will pop (out the intake I believe) on occasion wh...
1 2 3 4 5 6 7 Next >>   25 50 75
 

Last videos:

DIY: Fixing an exhaust leak
DIY: Fixing an exhaust leak
HCCI skyactiveX 2019 engine
HCCI skyactiveX 2019 engine
Carle's Corvette
Carle's Corvette
UUC Catback
UUC Catback
Strange Ticking Noise?
Strange Ticking Noise?
Check these out for working on your C7!
Check these out for working on your C7!
Got faded plastic trim?
Got faded plastic trim?
Wray's Corvette
Wray's Corvette

Tags

Cars ·
Travel ·
Pets ·
production-frontend
We use cookies for navigation analysis and personalized advertisement. By using our site, you agree to our use of cookies. Learn more