Forumsee logo
Forumsee » Cars » Maintenance & Repairs

Messages labeled as 'Ford'

1 2 3 4 5 6 7 Next >>   25 50 75

Today

what could i expect to make for safe hp with a stock untouched 140K mile ford explorer 302 completely stock except for cam (no idea on cam) and a very basic single B&G turbo kit-
I?ve been chasing my tail on my project trying to get my pushrod length dialed in. I've been reading through a bunch of threads on here and looking at youtube videos and it seem...
For a 97 GT with stock springs and stock K frame , what front springs would lower the front 1 inch ? Would like to retain the same spring rate or close to it .
I just installed a dual phantom fuel system. My question is how do I run the vent? I have a vent spot on the fuel hat but I?m not sure where to run the line to. Iv seen where ...
A while back the speedo on my '89 stopped working. It's the stock/original 140mph speedo in a 5-speed cruise control car. About 10 years ago the original speedo cable melted, s...
I have a 83 351w in my 90GT. It has comp 282xe roller cam with lunati link bar roller lifters, AFR 185 pedestal mount heads, and summit 1 piece 7.55 length pushrods. Problem is ...
I have some double 1.49 springs wth 130 seat and 350 open but with only a TFS 1 cam max open might be a max of 300#s. As short as they are I think they be fine. Think I'm using ...

Yesterday

I have a laundry list of fixes that I want to make that have me thinking it might just be easier, and I might do a better job, if I pull the engine. But, I have never pull...
I will need a new set of rocker covers for my windsor. Looking at some of the offerings and can't believe some of the prices, especially the billet stuff. I think a plain set ...
I have a tf box R Intake for 302. I want to run the standard R upper on my lower. Is the 302 different than the 351 upper? From pics, it appears to me that the 302 r ...
I have Edelbrock heads that were "O" ringed for Loc Wire gaskets some 23 years ago. Well, the HG's went this year. I figured I would change cam at this time too. Cam in now is a...
I have a 1990 manual Convertible 4 cyl with a nice rust free body but the dash was replaced and the harness was hacked to pieces. I purchased a 1990 8 cyl aod hatch with a ruste...
What?s a non plasma set of these without tires worth? Staggered fit. Thanks! Sent from my iPhone using Tapatalk
I'm looking to use FFRP-M6675DRS302 pan on my new motor and was wondering if anyone has used it with a MM-kmember with the 1 inch set back on the motor.
Guys, I've got a set of Hooker super competition 1-3/4 tubes on my 363. The tube for cylinders 3,4,and 8 have a removable slip fit tube for the headers to fit. Tubes 3 and 4 see...
Ok guys. here we go. I know many of you have done the brake swap many times and its simple. Bear with someone who typically doesn't mess with changing them. I never minded the b...
I've done it for years but think about it...When you purchase a new vehicle; do you break in the gears? The same goes for engines.
I just wanted to ask if anyone knew if you could attach fragola 6000 series stainless hose to steel tubing? I want to run 1/2? and 3/8? tubing and use the fragola hose for the s...

2 days ago

I got a set of iron heads with an o ring groove in them. The block does not have a receiving groove. I am cautious about running a copper head gasket on a street car becaus...
my cam is from Comp, and is part #35-000-9, serial #B4507-13... I don't know what that means... I do know it's a billet solid roller jobbie. My dizzy has a bronze gear on i...
Hey guys, I have a Dart 363 which I just confirmed is built like the late model roller blocks. I am using stock style lifters and spider/dogbones. My question is, if I want to...
Ex managed to destroy one of her rims on her Fiesta. Apart from the usual stealerships, anyone know where I can source a single rim? According to the size stamp it is a 15 x 6J
Hey guys just picked up a 1990 coupe roller that has been sitting for a few years. It was a friends that passed away unexpectedly several years ago. He did a 5 lug conversion an...
What's the most horsepower you guys have see out of a factory SD car? What was the setup and driveability like? Thanks!!

3 days ago

Hey guys, I'm pretty sure this is a common set up besides the cam but what do you guys think ill make at crank/wheel hp set up is stock HO 302 short block, trickflow tw 170...
1 2 3 4 5 6 7 Next >>   25 50 75
 

Last videos:

is this Nuno's office?
is this Nuno's office?
New Ls7 Stock Bottom End Record!
New Ls7 Stock Bottom End Record!
how to use your LS6
how to use your LS6
DPF overview
DPF overview
Air Filter Horror Story
Air Filter Horror Story
Mr Clean Paint Correction
Mr Clean Paint Correction
New YouTube Video! My Turbo Trans Am on the dyno. Do I still have 1000 Horsepower
New YouTube Video! My Turbo Trans Am on the dyno. Do I still have 1000 Horsepower
12 year old LS1 with a 200 shot of Nitrous
12 year old LS1 with a 200 shot of Nitrous

Tags

Cars ·
Travel ·
production-frontend
We use cookies for navigation analysis and personalized advertisement. By using our site, you agree to our use of cookies. Learn more