Forumsee logo
Forumsee » Cars » Maintenance & Repairs

Messages labeled as 'Chevrolet'

1 2 3 4 5 6 7 Next >>   25 50 75

Today

Having issue with brakes come and go. Few piece suspect.Master cylinder,air or vac leak. Wondering if booster can have internal leak since carb cleaner trick has not shown any l...
I need to replace my inner tie rods on my 2010 Silverado crew cab 5.3L. First time attempting this, but they will not come off with a wrench or $20 inner tie rod tool from Pep ...
Hello all!! as a new member to the forum I would like to ask a question. I have a broken windshield on my 1969 Impala 2dr sport coupe. I live in the Netherlands a...

Yesterday

I have a problem with my 4x4 the actuator and transfer case motor are working but won't stay engaged any ideas?
I have a 68 with a Low Hump and already installed a 700R4 trans and am going to be installing a Big Block. I am doing the engine swap as close to original as possible. Did all...

2 days ago

Wondering if someone has some insight on what my cars issue may be. 86 monte with a gen 1 setup.....desmogged 350....turbo 350, no comp......but lately it has started surging th...
Just finished installing my 6.0 with a 4L65 and having an issue with it popping out of drive, while driving down the road. Anyone else experience this and is there a fix?
If you would like a free board 2018 Calendar, click on ole LINKY for details.
1st time frame off cant remember how the vacuum hoses hook back up. there are 6 hookups- vacuum Actuator for kick panel inside the cab,vacuum Actuator cowl on firewall,vacuum ta...
I have the vortec cast heads that are going on my 72K10 with a cam that has .432/.453 lift and I was wondering if these pressed in rocker studs are a concern to anybody? Do you ...
For the past 3 years i have wondered what rearend is in my truck. Today i started tearing it apart to fix an on going bearing whine and now i need to know. All the catalogs that...
Does anyone know if a 1978 Lincoln Mark 5, 9" disk rear is a 5 on 5 bolt pattern??? I have searched and seen the 77, 9" rear is... but unsure about the 78 model. Regar...
For those of you that have a T56/LS combo: Did you have enough clearance to leave the stock crossmember in place? I asked this question in my build thread but got no response s...

3 days ago

Question about hydro boost and interchangablity with newer models. My 69 panels hydro boost seems to be in question in cpl ways. I have few donor vehicles sitting around and won...
I picked up a 98 chevy c1500 350 this evening and I will be needing to fix the mess the previous owner made of the shifter. The previous owner even left me a new unit like this ...
Hey I was wondering how you would go about lifting a vehicle with this front end without a body lift and maybe without a spindle lift. But if I had to use a spindle lift, the h...
08 tahoe ls with 4.8l about a year of owning the truck truck out of no where i get the indication on my DIC engine hot ac off... http://rd.bizrate.com/rd?t=h...
Been driving my 69 Panel quite a bit and noticing rearend is getting little louder. Figure not too long before it lets go. Looking go another 12 bolt that will basically bo...

4 days ago

Need to upgrade. Curious if anyone has had a great experience with a particular product... Leaning towards HID but eager to hear. Just don't want to take the time and money to...
I have a 2013 Chevy shortbed silverado... I bought it already lowered. The problem is it rides so rough. Do they make a softer shock to allow some softer movement? The rear seem...
maybe someone can shed some light on this problem. My truck is just not running right and I wonder if I have a fuel pump problem. I?m throwing a service engine soon light ( off ...
I have to replace the pinion seal on my front dana 44 but need the torque spec for tightening the nut up on the yoke?

5 days ago

So I am getting ready to start the engine in my C10 and it ran good before I parked it. Besides the obvious like new fluids and plugs. What else would you recommend I do before ...
After rebuilding the transmission I filled it with the proper weight/rating gear lube. Later noticed that the container was labeled "GL-5 rated". Now i have seen that the GL-5...
Good evening, Bought my 63 step with a 327 and 3 on the tree this summer. Didn't get to drive it much before the 327 gave out. Just got my 290 hp GM performance 350 crate a...
1 2 3 4 5 6 7 Next >>   25 50 75
 

Last videos:

is this Nuno's office?
is this Nuno's office?
New Ls7 Stock Bottom End Record!
New Ls7 Stock Bottom End Record!
how to use your LS6
how to use your LS6
DPF overview
DPF overview
Air Filter Horror Story
Air Filter Horror Story
Mr Clean Paint Correction
Mr Clean Paint Correction
New YouTube Video! My Turbo Trans Am on the dyno. Do I still have 1000 Horsepower
New YouTube Video! My Turbo Trans Am on the dyno. Do I still have 1000 Horsepower
12 year old LS1 with a 200 shot of Nitrous
12 year old LS1 with a 200 shot of Nitrous

Tags

Cars ·
Travel ·
production-frontend
We use cookies for navigation analysis and personalized advertisement. By using our site, you agree to our use of cookies. Learn more