Forumsee logo
Forumsee » Cars » Performance & tuning

Performance and tuning

<< Prev 1   ...   4 5 6 7 8 9 10 Next >>   25 50 75

7 days ago

Im having a little problem maybe you guys can help me with. I had a Cobb AP3 for my 2014 Mitsubishi lancer evolution gsr and it went missing out the car. The issue that im havin...

8 days ago

I finally installed AEM ems v2 (30-6050) on 2002 is300. Upgraded from GEmu. Can someone help or send me base start up cal for 2jzge na-t. 550cc injc GM IAT AEM 5bar map ...
Anyone have a file for a stock tune for my evo 8. Trying to fix the issue. Long story short the car was apparently built and tuned but some time down the line it got a stock mot...
Hello guys, Entering specs into the performance trends computer software. I have two engines a KLDE and a KLZE. I need the cam specs for both engines. centerlines intake and exh...
Need some expert help on LS engine build for my super gas tube chassis build. This is a all new build, The Truck will be run primarily in brackets not looking to run any NHRA su...
This thread is intended to add a few helpful comments to > Canadian Spec DRL Modification by Will Brown > https://www.miata.net/garage/cdrl/cdn-drl.htm The Canadian modu...
I'm looking for how high the Raceland Windblocker is from the rear deck to the wind blocker's top tube. I'm thinking about putting one in but concerned the bar will cut down th...
Did a search, couldn't find anything. I guess here in the US, the dashboard has 2 inserts directly below the diver's side air vent. I'm trying to find the version with 3 in...
So over the years I've added first a Super Q, later a GW mid-pipe, and just recently a GW Max header. At each stage I've used VirtualDyno to measure performance. The Super Q...
Installed this diff in factory spec two years ago then this car become very understeer as soon as I touched the gas pedal because it locks so fast and so tight. Tried many thing...
Seems that running HFC will sure give you a P2098 code, running too lean. For those that got this code, how were you able to resolve the issue? I know some say to get a tu...
Where do I change the settings for vss pulses in hp tuners? using a dakota digital 8k signal generator and what should i change settings to. Car has 4:10 gears and a 26.7 in re...
I have a 0411 PCM 2004 and want to set the fan control so that they are activated by engine/cooling temps and not A/C conditions or via the BCM (fan1) Is this possible as I ...
Hey guys it is my first time on here which means I am at my breaking point with my 69 C10 project. I have integrated an LS3 Blueprint LS427 with the GMPP harness and operating s...
Got a small clamp on the clip first and pushed the clip together. The lower one is ruthless the upper one goes on easy if you open up pliers and place over the edge of clip. Adv...
Just wondering if anyone knows what this could be and if I should be doing anything to clean it or just let it be. Turbo is brand new, just installing now and took the red en...
It seems like there is boost issue of some sort, when punching it the turbos will all of a sudden stop working like the pressure becomes to high and they shut off to save the mo...
So I'm starting in on the cooling system. The upper hose had a pin hole leak and created a little geyser under the hood. Progress has been a bit slow as I'm coming back from an ...
Want to level my C4 .bought a 1""drop bolt kit .thought it would be simple .I installed the new bolts and bushings the car sat up higher in rear then it was .so I decided to put...
It's Sunday morning so I'm already studying you FSM on today's project; adjusting the rear ride height on my '91 ZR1. I was waxing (yes, I DO wax along with spinning as man...
Ok, haven't found this exact issue discussed. Most people doing a swap leave the auto TB/TPS and that's that.. but I need it for another car so please don't say "keep the auto ...
First off, I apologize, if this has been asked before? I've been doing a good but of research on both the Rotrex S/C from TDR and an Ecotec 2.4 swap. Yesterday, I found a ...
hey guys i have a cobb ap and im seeing knock with this unit and am scared. i want a tuner that can etune my car for me. anyone know of someone reputable. My mods are cobb ap, h...
so i'm installing my supercharger buti cant get my 550cc r\c injector to sit tightly in there...i check all the o -rings and everything sits fine but nut snug feels like there i...
Finally decided to go for it and the 20" wheels are coming off my S5. I have bought a set of the double spoke 19's. Have many of you done this? Will it give me the more comf...
<< Prev 1   ...   4 5 6 7 8 9 10 Next >>   25 50 75
 

Last videos:

Aristo Throttle Body
Aristo Throttle Body
Crystallized brightness
Crystallized brightness
Kufatec A5
Kufatec A5
Jericho 5 speed?
Jericho 5 speed?
Jericho 5 speed?
Jericho 5 speed?
great video for noobs who want to see how the whole enchilada is put together
great video for noobs who want to see how the whole enchilada is put together
Balance Shaft Elimination Questions
Balance Shaft Elimination Questions
Balance Shaft Elimination Questions
Balance Shaft Elimination Questions

Tags

Cars ·
Travel ·
Pets ·
production-frontend
We use cookies for navigation analysis and personalized advertisement. By using our site, you agree to our use of cookies. Learn more