Forumsee logo
Forumsee » Cars » Classic cars

Classic cars

<< Prev 1   ...   2 3 4 5 6 7 8 Next >>   25 50 75

3 days ago

My stock radiator was a 3 core and the spectra replacement doesn't fit in the pads. Does anyone know if the 4 core pads will work or should I make my own? Thanks
I rebuilt the MonoJet on my 72 C10. The 250 runs great, but I did notice something that might be a problem. I was tinkering with the air valve dashpot, and noticed that wh...
After painting the hood, I have three chevrolet hood letters with broken posts. The long post on these three is too short to hold a nut. Anyone with any suggestions for how to...
Ok guys this is my first build and it?s been alittle over 3 years. Here is my issue. The motor is a 383 which dynoed at 472hp. The transmission is a B&M 700r4. Inland empire dri...
The Healey Seaside Summit promises to be an outstanding event on Boston's North Shore. Not too early to start thinking about next year's Healey summer vacation. The Austin-Heale...
I am about to replace the connecting rod and center main bearings on my 100 and do not understand the following statement in the Service Manual: "Main Bearing Stud Nuts/Con...
I changed the rear diff oil today and had both rear wheels up on jack stands. While it was up I rotated the rear wheels to check for brake drag, and while there was none, there...
Good day fellas, does anyone have suggestions on the best fit reproduction front fenders and inner fenders for a 56 3100? I'm the excited new owner of a 56 3100 with a big windo...
Have a 48 suburban with a monte carlo 305 in it. seems i am seeing a large oil puddle under it after running it in place for a bit. Traced it up to the passenger side of vehic...
I keep eyeing the powered rear hatch mechanism on my 2012 Acadia and have wondered if I could make something like that work on my hood. Thoughts??
Long time 1st Gen Camaro fan, ...finally jumping into the Chevy Trucks I've been looking at this one for a few years, but passed on it since it's a long bed (like many, I a...
Addressing some wiring issues on the 66 I bought a few months ago and need some assistance. Original ignition switch had been replaced with a universal switch and separate start...
somewhere around 1975 i put a cheap jc whitney carpet in my truck, i think i was trying to impress my gf , because back then i barely had money for gas. in my memory i thought ...
Does anyone know if the 66 c10 front wheel bearing hubs are the same as the 67 front wheel bearing hubs?
doing a new cab on a 83 k-30 chassis/85 cab -350 motor has a alum. intake w/small holley -my factory linkage -does not have enough travel to open carb ?? i did buy a "edelbroc t...
So the TKO showed up. I hit a wierd spot where I have no other running vehicle so.... to install this on my stock bellhousing I need the adapter ring to adapt to the larger truc...
I have had my Suburban for a little over 4 years now. I have already swapped a 6.0/4L80 into it last year. I have always had in the back of my mind that I would like to low...
My brother and I bought a Blazer out of Albuquerque New Mexico in August of 2012. Started to replace the carpet and noticed three holes in the passenger side floor board. The ho...
looking to do an upgrade on the 69 Chevy C10 Gas Pedal. Anyone know if the 73 C10 Assembly is the same as the 71-72? Some of the parts look to be the same on LMC catalog but n...
Periodically, I receive emails from Chevrolet. Here's a link from the one I got today. Contains a couple pictures of one of our trucks. I'm wondering if the truck in the feature...
The column shifter on my '69 C20 ( 350V8 / Turbo400 ) is very loose while shifting from park into reverse and into drive... I know that this can be adjusted, just that I never ...
Hey all, So the other day I noticed something was leaking from the drivers side of my rear axle. The truck is a '68 K20 and has the eaton HO52 axle. I noticed something ha...
The mirror glass in one of my 72 rear-views is cracked - the rest of the item is in good shape. Anyone had success in finding or having made a replacement pane - and installing...
Does anyone have pictures that show where they mount? Next step in build. And haven't had any luck finding this information. Help appreciated. Don't have access to Photo Buck...
Ok I searched and didn't find the answer sooo.......are there any differences between the 350 and 402 air cleaner spacers other than the hose and the end at the valve cover ??...
<< Prev 1   ...   2 3 4 5 6 7 8 Next >>   25 50 75
 

Last videos:

Battery cable video. What do you think?
Battery cable video. What do you think?
100 Years...
100 Years...
And bang....
And bang....
Headquake RC
Headquake RC
Why You SHOULD NOT Buy A 2017 Audi Q7 (and Q5?)!
Why You SHOULD NOT Buy A 2017 Audi Q7 (and Q5?)!
Chevy Tough
Chevy Tough
You Really Should Reconsider
You Really Should Reconsider
Muffler bearings
Muffler bearings

Tags

Cars ·
Travel ·
Pets ·
production-frontend
We use cookies for navigation analysis and personalized advertisement. By using our site, you agree to our use of cookies. Learn more