Forumsee logo
Forumsee » Cars » Classic cars

Classic cars

<< Prev 1 2 3 4 5 6 7 Next >>   25 50 75

Yesterday

Any suggestions? Thinking to run along the passenger side frame to rear tank. Thoughts on vapor return line too? Thanks
Looking for some photos for some ideas. I installed a POL booster and master cylinder setup. Best option from there to the front and rear brakes??
Good evening, Bought my 63 step with a 327 and 3 on the tree this summer. Didn't get to drive it much before the 327 gave out. Just got my 290 hp GM performance 350 c...
Ok...I've been doing lots of reading here about various Quadrajet & timing issues. I have been getting what I would consider lousy mpg(4-5) and driving at highway speed seems to...
Hey guys. I just got an 86 square. I replaced the radiator and flushed the whole cooling system and put in a 190 degree thermostat. What should be the normal running temp. It al...
The more you use, the more you have.I have learned over the years that when one’s mind is made up, this diminishes fear.I would rather die of passion than of boredom.A truly ri...
Anyone have any problems with this lift? I did the 4" all spring lift and it sagged a little on the drivers side both front and back, (didnt sag before the lift) I figured the s...
I wanted to confirm whether or not this is a factory rear speaker. It's wired all the way to the factory radio. I have never seen one but heard they did come with one as a rarer...
I have a question and I'm sure I will get a lot of suggestions, I'm just looking for the best solution so I only spend the money once. I have a 68 with a SB350mild cam and TH350...
Hi guys. I just posted a couple of Highway 61 C-10s for sale in the "Misc/Everything Else" section: Black '72 http://67-72chevytrucks.com/vboard/c...ck-1972&cat=18 ...
I searched through a lot of throttle cable bracket threads and have seen a lot of use of aftermarket style brackets. I was wondering if anyone has used a bracket off a GM car? I...
Has anyone swapped a LS3 engine and TR6060 tranny combo into a C10? I've got a 67 C10 that I'd like to try this on. I'm having a forged motor built for my 2010 Camaro and I wa...
Popped out my u-joints using the hammer, wood block, impact socket and drift method (on the concrete floor. New U-joints are the right part number, dimensional - look to be...
I have ran up on this ruck and may have an opportunity to buy it. I have always wanted a Cheyenne and have been watching this one for a while and it has come up for sale. It has...
I need to know how to read the serial number off my np205 transfer case so i can know how many splines it has because im wanting to do an ls 5.3 swap and i need it to mate up to...
My" body guy offered to do the fenders, but he hasn't seen the results of blasting yet. My first blasting experience.........Hired a shop actually, I don't have an adequate com...
I've been in the process of installing new suspension parts and now working on screwing in the grease fittings on the bushings/ball joints. I have 2 that I can't get going. ...
For about a year+ I've had an eBay wishlist looking for an air pressure gauge that would fit our dash (where the spare, or the Vacuum gauge is often placed). I was hoping maybe...
This is the nut for the spare tire carrier. I don't have one but it's on order. I plan on fabricating the bolt that goes with it out of allthread. Can anyone help with the t...
Curious how guy's media blast and rebuild/ paint door hinges but still have the pins and bushings looking factory? Any tips? Thanks guys.
Hi guys, I've got a 67 C10 fleetside short that I'm starting a build on. First time building a C10. Would like some help with wheel/tire fitment. Wondering if I ca...
Just had a service, even topped up water and screen wash for 99p But now in this snow, I’ve no screen wash. It is frozen in the nozzles I guess. What? a £60k car and they ...
Hello all, After much deliberation we have just placed a deposit on a 65 plate SQ5 with Teeside Audi We have been on the lookout for a Sepang Blue SQ5 for a while and hav...

2 days ago

Floor plates one has some holes but has been blasted shouldn't be a bad fix 35 shipped Windshield corners 25 for the pair plus shipping or 15 ea. plus shipping. Pieces where ...
Today I was driving down the road and my column shifter lever just came loose from the prong that it is fastened to. It looked like some rivets hold this in place in the top an...
<< Prev 1 2 3 4 5 6 7 Next >>   25 50 75
 

Last videos:

Battery cable video. What do you think?
Battery cable video. What do you think?
100 Years...
100 Years...
And bang....
And bang....
Headquake RC
Headquake RC
Why You SHOULD NOT Buy A 2017 Audi Q7 (and Q5?)!
Why You SHOULD NOT Buy A 2017 Audi Q7 (and Q5?)!
Chevy Tough
Chevy Tough
You Really Should Reconsider
You Really Should Reconsider
Muffler bearings
Muffler bearings

Tags

Cars ·
Travel ·
production-frontend
We use cookies for navigation analysis and personalized advertisement. By using our site, you agree to our use of cookies. Learn more