Forumsee logo
Forumsee » Cars » Classic cars

Classic cars

1 2 3 4 5 6 7 Next >>   25 50 75

Today

Should be mine in a few weeks.. Hope the upload worked! Attached File(s) -  new motor.jpg (124.18K) Number of downloads: 39
Shifter boot ring 30 shipped e-brake cable I have both connector ends but not pictures 30 shipped Filler neck 60 shipped Side reflectors have some cracks 25 shipped
Hey everybody, I have been following this website for a while and finally decided to start a project thread. I got a 1965 Chevy C10 panel truck two years ago. It was mostly comp...
Just brought this 54 3/4 ton home this afternoon. Been siting in a old layer house for the last 37 years. Previous owner bought it in 1958 and parked it around 1980/91 Its in pr...
Anybody here have any input on the Dakota Digital VHX clusters? My choices have narrowed down to blue or white backlighting, just not sure of bezel color yet...silver or black. ...
I'm doing an LS swap into a 1995 2door Tahoe. While removing the harness that goes to the 4wd switch, VSS and the two to the front diff, there's also a 4 prong harness that's ti...
I bought a 1/2 ton with a 5 inch rear drop. No notch. Looks like stock shocks. Hard ride and it bottoms out. Thinking about air shocks, but don't know which ones to get? Ju...
So I have owned this truck for 10 years and it has worn many hats in its time. She has been in cold storage for the last 4 years. I started gathering parts for the rebuild and f...
I have a spare cab sitting around that I?m not going to use. Curious what it?s worth, if much at all. The cab was from a 1970 C20, it does have rust, mainly in the drivers side ...
I have a '65 GMC the original guage was complety useless so I bought a gas guage and sending unit from Speedway Motors. Now that I have it installed the needle goes straight to ...
The cab on my 66 sits about an inch higher on the passenger side. I pulled the passenger side mounts off and with part of the cab touching the frame it is about level. All but o...
In typical Izzy style, I bought another one! Another 99-07 GM truck of some sort that is. As the title of this thread indicates, I purchased a 2003 Avalanche for my 18 year ol...
Has anyone had issues with the ecd-100 no reading the signal from the trans (6L80E). I have been told it's in the computer flashing and my take sever times to get the signal. An...
Just had my truck blasted to bare metal. What should I treat it with to prevent surface rust before I can get it into the body shop? Posted via Mobile Device
I am kinda stuck on something and hopefully someone can assist me. I am replacing the fuel lines on my stock 1972 C/10 LWB with SBC350/TH350 and the tank in the cab. I just p...
Has any used the aftermarket rams horn manifolds on our trucks?I was looking at the ones from Jegs and Summitt,they are center dump and I was wondering about crossmember clearan...
I have a small Holley 4bbl on an offy intake. Routed the coolant water to the intake manifold bottom plate from the left side of the head. The outlet I was going to route int...
I installed a new harness from Painless Wiring, but not sure where to connect the e-brake wire. Should I just terminate it and leave it disconnected? As far as ive always know...
have you relocated your battery to hide it from thieves and put a disconnect on it with a key so when you park it you can shut down all the power?? If so please show your set u...
Dad and I removed the thermostat today in preparation for flushing the water jacket. He suggested I boil it to test it. It opened just after boiling temp was reached and c...
What do you all think?? Sent our aluminum grill to be chromed. This is how it turned out. Now do we get a chromed center plastic or put stock silver back in it??
hey guys I am new to this site.hopefully someone can help me out.I have a 1959 100-6 healy,that I started to restore 20 years ago.I am now in the process of taking apart because...
Any one know where i could find a used B&M 177 or 174 iv look everywhere i know to look and cant find one this will be the end of my search b4 i go with a centrifugal supercharger
I’m getting a 1275 with 5 speed plate reworked and it has a rear oil seal kit on it. Can anyone tell me what brand it might be? It was covered in clear silicone as was the oil...
The PO installed this white thingy next to the condenser on the engine of my newly-acquired 1957 TR3. Any ideas what it might be?
1 2 3 4 5 6 7 Next >>   25 50 75
 

Last videos:

Battery cable video. What do you think?
Battery cable video. What do you think?
100 Years...
100 Years...
And bang....
And bang....
Headquake RC
Headquake RC
Why You SHOULD NOT Buy A 2017 Audi Q7 (and Q5?)!
Why You SHOULD NOT Buy A 2017 Audi Q7 (and Q5?)!
Chevy Tough
Chevy Tough
You Really Should Reconsider
You Really Should Reconsider
Muffler bearings
Muffler bearings

Tags

Cars ·
Travel ·
Pets ·
production-frontend
We use cookies for navigation analysis and personalized advertisement. By using our site, you agree to our use of cookies. Learn more