Forumsee logo
Forumsee » Cars

Messages labeled as 'Chevrolet'

<< Prev 1   ...   2 3 4 5 6 7 8 Next >>   25 50 75

2 days ago

I am considering a 08 Tahoe hybrid. I like the looks/styling and the powerful 6.0L plus I enjoy hybrids. I occasionally move cars with a transport trailer and wondered how these...

3 days ago

Im wanting to put a 6.0 engine and 4l80 trans into my 68 truck. I've been looking around at prices for just the engine and trans that are suppose to come complete with everythi...
For those of you in the market for tires, you might get a quote from your local Sam's club. I know,I know a big box store, but read me out. I priced BF Goodrich AT2 31X10.50X15....
Folks, need some help from forum members. Just picked up a '68 C10 (2wd) that I am getting ready for an engine break in after I get everything connected. I bought the truck wi...
Ok, looking for thoughts on gear ratios for my tow truck. Truck is a 69 C10 350/T400, 12 bolt rear with 33" tires. Load is a jetski trailer approximately 2,000lbs, plus maybe 40...
I picked up this small block this morning ,it's a fresh rebuild and I bought it for less than the cost of the parts showing .New hei dist /wires/starter/water pump/fuel pump/ ra...
Hey everyone, my name is Alex and I'm new to the form. I've recently purchased a couple of trucks a 1969 long bed c10 and a 1971 K10 short bed. The K10 is missing the glove box ...
If you have one or have any pictures of any white trucks. Due to my minor mistakes on body work since im not a professional and because white is usually cheaper, well thats wh...
Hello I have a stock 1968 C10 short bed. It has an un modified 305 small block with the cast manifolds. I'm looking for a set of headers that will bolt directly in the stock man...
What do you guys think of these? do you think they would look good..... now all I have to do is find some 20 inch white letter tires http://www.newstalgiawheel.com/listp....as...
Hey guys i need some help. My dad is tellin me the only way to get ball joints out(without a separator) is to just beat and beat and beat on them. It took us four and a half hou...
Question about hydro boost and interchangablity with newer models. My 69 panels hydro boost seems to be in question in cpl ways. I have few donor vehicles sitting around and won...
I have a 1989 Georgie Boy RV with a 454 7.4 L big block. I have been trying on the internet to find a repair manual for the engine as configured in the bus so far no luck. I w...
Most of the time, you don't want to think about having to call a tow truck, because generally, that means bad things. But regardless of the problem that left you stranded, if yo...
Hello All; I have a 57 panel truck that I;m trying to find more info on. I have ft fenders an a grille. I do not have the upper of lower fender supports. To mock ...
I am looking for a factory piece of single wall top side glass for the passenger side. Not sure if both sides are the same? Glass needs to have factory tint, if I can't find jus...
I tried the drop arm peep mirrors but they are too small and the passenger side is virtually useless for the reason listed below. Been searching for a set of door mirrors othe...
So i scored a 1969 K10 Blazer today for $300 has a 250 straight 6 with a 3 speed on column and it runs.. research has shown there was 58 made of the KE10703 and KE10734 had a pr...
On the way to the dump and stopped for a bite. Came out and found this in front of the 3+3... Wish I woulda unloaded the can for the pic but it was 16 degrees and I was in a hur...
here's an idea of what i'm looking to do with my truck... http://67-72chevytrucks.com/vboard/s...87#post1789187 what do you guys think, stock grill (my truck) vs. a b...
Looking at having the sides of my truck done in wood vinyl which one do you like best? i'm leaning too top photo middle one or second photo far left The truc...
I picked up a 98 chevy c1500 350 this evening and I will be needing to fix the mess the previous owner made of the shifter. The previous owner even left me a new unit like this ...
Hey I was wondering how you would go about lifting a vehicle with this front end without a body lift and maybe without a spindle lift. But if I had to use a spindle lift, the h...
08 tahoe ls with 4.8l about a year of owning the truck truck out of no where i get the indication on my DIC engine hot ac off... http://rd.bizrate.com/rd?t=h...
So i scored a 1969 K10 Blazer today for $300 has a 250 straight 6 with a 3 speed on column and it runs.. research has shown there was 58 made of the KE10703 and KE10734 had a pr...
<< Prev 1   ...   2 3 4 5 6 7 8 Next >>   25 50 75
 

Last videos:

Noise at steering
Noise at steering
Video about Premium Fuel
Video about Premium Fuel
Giants Despair 2017
Giants Despair 2017
Are you getting the ZR1?
Are you getting the ZR1?
Scottsdale Cars & Coffee
Scottsdale Cars & Coffee
now this is cool!
now this is cool!
Loudest C63 ?
Loudest C63 ?
Greenwood Corvette at Daytona
Greenwood Corvette at Daytona

Tags

Cars ·
Travel ·
production-frontend
We use cookies for navigation analysis and personalized advertisement. By using our site, you agree to our use of cookies. Learn more